Fuel Injector Sleeve RE518339 RE531334 for John Deere Engine 10.5L 12.5L 13.5L 6105 6125 6135 Tractor 9100 7400 7200 7300 7350 7380 7450 7480

Fuel Injector Sleeve RE518339 RE531334 for John Deere Engine 10.5L 12.5L 13.5L 6105 6125 6135 Tractor 9100 7400 7200 7300 7350 7380 7450 7480

This fuel injector is engineered as a direct replacement for the John Deere Engine 10.5L 12.5L 13.5L 6105 6125 6135 Tractor 9100 7400 7200 7300 7350 7380 7450 7480. Manufactured to meet or exceed OEM specifications, it delivers reliable performance in demanding conditions. Each unit is tested for fuel flow, pressure rating, and durability before leaving the factory to ensure consistent quality across every order.

Vehicle Compatibility

Replaces OEM Part Numbers

RE518339 • RE531334 • Deere • Engine • 6105AF100 • 6105HF100 • 6125AF001 • 6125HF001 • 6125HF070 • 6135HH001 • 6135HH002 • 6135HRW01

Signs You Need a Replacement

If your equipment is showing any of these symptoms, the injectors & nozzle may be the cause:

• Rough idle or misfire — Uneven fuel delivery from a worn injector causes the engine to shake at idle. On John Deere engines, this is often accompanied by a knocking sound under load.
• Black or white exhaust smoke — Black smoke means excess fuel; white smoke indicates incomplete combustion. Both point to injector spray pattern degradation.
• Loss of engine power — A single failing injector reduces cylinder output. Multi-cylinder engines lose noticeable power when one injector flows less than the rest.
• Increased fuel consumption — Poor atomization means the engine burns more fuel to produce the same power. Monitor your fuel burn rate as an early warning sign.
• Hard starting or no start — If the injector doesn’t deliver fuel on cranking, the cylinder won’t fire. This is especially common in cold weather with worn nozzles.
• Fuel in engine oil (dilution) — Fuel leaking past the injector seat seal contaminates the crankcase oil. If the oil level rises or smells of diesel, inspect the injectors immediately.

Replace as a Set

Replace all injectors as a set whenever possible. On John Deere engines, mixing old and new injectors creates uneven fuel delivery — the new injectors compensate for the worn ones, shortening their life. When installing, use new copper sealing washers and torque to the specification in the service manual. After installation, run the engine at idle for 5 minutes to bleed air from the fuel system, then check for leaks at each injector connection before putting the machine under load.

Frequently Asked Questions

Will this fit my John Deere 6105?
Yes. This part is designed to fit the John Deere 6105, 6125, 6135, 9100 among other models listed in the compatibility table above. Verify your specific model and engine code before ordering to ensure the correct fit.

Can I cross-reference RE518339 with RE531334?
Yes. Both RE518339 and RE531334 are interchangeable OEM numbers for this part. They refer to the same component with the same specifications, just different part number revisions.

How do I check if my engine code (QSX15) matches?
The engine code is stamped on a metal tag attached to the engine block, usually near the timing belt cover or on the cylinder head. Compare the code you find with the list above. Engine codes are 3 to 6 characters long.

What are the common failure signs on a John Deere engine?
On John Deere engines, watch for black exhaust smoke under load, rough idle, misfire codes (P0300 series), and loss of power. A single failing injector can reduce engine output by up to 25%. If you notice fuel in the engine oil, the injector seat seal is likely compromised.

You May Also Need