4 Pieces Fuel Injection Pump Plunger 15221-51050 for Kubota Engine D1102-AE-1 Excavator KX101 KX151 KH-90 KX040-4
This fuel pump is engineered as a direct replacement for the Kubota Engine D1102-AE-1 Excavator KX101 KX151 KH-90 KX040-4. Manufactured to meet or exceed OEM specifications, it delivers reliable performance in demanding conditions. Each unit is tested for fuel flow, pressure rating, and durability before leaving the factory to ensure consistent quality across every order.
Vehicle Compatibility
| Application | Details |
|---|---|
| Kubota Engine D1102 | AE-1 Excavator KX101 KX151 KH-90 KX040-4 Replacement Part Number: 15221-51050, 70000-65193, 090150-1160, 1522151050, 7000065193, 0901501160 Fit for |
| Kubota Engine: D1102 | AE-1 Applications:Fit for following models |
| Kubota Generator: GV1120 | B-50-AUS, GV1160-B-50-AUS, GV3100-B-50-AUS, GV3120-60-B, GV3150-B-50-AUS, GV-3170(SW), GV3200-B-50-AUS |
| Kubota Excavator: KD | 15(S), KH-1 10, KH-101, KH-101KTA, KH-151, KH-170L, KH-191, KH-191EXP, KH-28, KH-28L, KH-60, KH-60(H), KH-60H, KH-66, KH-66HEXP, KH-66KE, KH-70(H), KH-90, KH-90(H), KH-90H, KH-91, KH-91H, KH-H KCL, KX101, KX151 |
| Kubota Loader: R400(B), R410, R410B, RC | 20FD, RW25, RW30 |
Replaces OEM Part Numbers
15221-51050 • 70000-65193 • 090150-1160 • 1522151050 • 7000065193 • 0901501160 • Kubota • Engine • D1102-AE-1
Signs You Need a Replacement
If your equipment is showing any of these symptoms, the injection pump may be the cause:
- Engine cranks but won’t start — The pump may have lost prime or stopped delivering fuel. Check for fuel at the filter outlet before replacing the pump.
- Stalling under load — A weak pump can’t maintain pressure at high demand. The engine runs fine at idle but dies when you put it to work.
- Fuel pressure warning (if equipped) — Modern Kubota equipment monitors fuel rail pressure. A low-pressure warning often means the pump is failing.
- Loud whining from fuel system — A failing pump makes a high-pitched whine that gets louder as it warms up. Normal pump noise is a low hum.
- Air in fuel lines — If you see bubbles in the transparent fuel line or the primer bulb won’t stay firm, the pump may be drawing air through a worn seal.
- Excessive return flow — Too much fuel returning to the tank instead of reaching the injectors indicates internal pump wear.
Before You Replace the Pump
Before replacing the pump, check the fuel filter and fuel lines for restrictions. A blocked filter causes the same symptoms as a failing pump on Kubota equipment. When installing the new pump, fill it with clean fuel before connecting the lines — this reduces priming time and prevents dry-run damage. After installation, bleed the system fully and check for leaks at all connection points. Replace the fuel filter at the same time as the pump to protect the new unit from debris.
Frequently Asked Questions
Will this fit my Kubota KX101?
Yes. This part is designed to fit the Kubota KX101, KX151, KX040-4 among other models listed in the compatibility table above. Verify your specific model and engine code before ordering to ensure the correct fit.
Can I cross-reference 15221-51050 with 70000-65193?
Yes. Both 15221-51050 and 70000-65193 are interchangeable OEM numbers for this part. They refer to the same component with the same specifications, just different part number revisions.
How do I check if my engine code (KX101, KX151, KX040, RW25) matches?
The engine code is stamped on a metal tag attached to the engine block, usually near the timing belt cover or on the cylinder head. Compare the code you find with the list above. Engine codes are 3 to 6 characters long.
This listing is for 4 pieces – do I need to buy a full set?
This listing includes 4 units. For best results, replace all injectors at the same time rather than one at a time. Mixing old and new units causes uneven fuel delivery and shortens the life of the new parts.
Reviews
There are no reviews yet.