Fuel Pump RE500375 for John Deere 4045 6068 Engine 120 160LC 200LC 230LC 270LC 330B 435 2254
This fuel pump is engineered as a direct replacement for the John Deere 4045 6068 Engine 120 160LC 200LC 230LC 270LC 330B 435 2254. Manufactured to meet or exceed OEM specifications, it delivers reliable performance in demanding conditions. Each unit is tested for fuel flow, pressure rating, and durability before leaving the factory to ensure consistent quality across every order.
Vehicle Compatibility
| Application | Details |
|---|---|
| John Deere 4045 6068 Engine 120 160LC 200LC 230LC 270LC 330B 435 2254 Replace Part Number:RE500375, 092100 | 3130, 0921003130 Fit for Engine |
| John Deere Excavator: 120, 160LC, 200LC, 230LC, 230LCR, 230LCRD, 270LC | See product specifications |
| John Deere Loader: 330B, 335, 430B, 435, 624H, 624H LL, 643H, 648G, 648G | II, 648G-III, 843H, TC62H, 2254 |
| John Deere Skidder: 460D, 540G, 548G, 640G, 640G | II, 640G-III, 643G, 653G, 740G, 748G, 843 |
| John Deere Sprayer: 4700, 4710 | See product specifications |
| John Deere Feller Buncher: 653E, 740, 840 | See product specifications |
| John Deere Motor Grader: 670C, 670CH, 672CH | See product specifications |
| John Deere Tractor: 7810 | See product specifications |
Replaces OEM Part Numbers
RE500375 • 092100-3130 • 0921003130 • Engine • Deere • 4045HP050 • 4045HP051 • 4045TP053 • 4045TT052 • 4045TT055 • 6068HDW50 • 6068HDW53
Signs You Need a Replacement
If your equipment is showing any of these symptoms, the fuel pump may be the cause:
- Engine cranks but won’t start — The pump may have lost prime or stopped delivering fuel. Check for fuel at the filter outlet before replacing the pump.
- Stalling under load — A weak pump can’t maintain pressure at high demand. The engine runs fine at idle but dies when you put it to work.
- Fuel pressure warning (if equipped) — Modern John Deere equipment monitors fuel rail pressure. A low-pressure warning often means the pump is failing.
- Loud whining from fuel system — A failing pump makes a high-pitched whine that gets louder as it warms up. Normal pump noise is a low hum.
- Air in fuel lines — If you see bubbles in the transparent fuel line or the primer bulb won’t stay firm, the pump may be drawing air through a worn seal.
- Excessive return flow — Too much fuel returning to the tank instead of reaching the injectors indicates internal pump wear.
Before You Replace the Pump
Before replacing the pump, check the fuel filter and fuel lines for restrictions. A blocked filter causes the same symptoms as a failing pump on John Deere equipment. When installing the new pump, fill it with clean fuel before connecting the lines — this reduces priming time and prevents dry-run damage. After installation, bleed the system fully and check for leaks at all connection points. Replace the fuel filter at the same time as the pump to protect the new unit from debris.
Frequently Asked Questions
Will this fit my John Deere 4045?
Yes. This part is designed to fit the John Deere 4045, 6068, 120, 330B among other models listed in the compatibility table above. Verify your specific model and engine code before ordering to ensure the correct fit.
Can I cross-reference RE500375 with 092100-3130?
Yes. Both RE500375 and 092100-3130 are interchangeable OEM numbers for this part. They refer to the same component with the same specifications, just different part number revisions.
How do I check if my engine code (TC62H) matches?
The engine code is stamped on a metal tag attached to the engine block, usually near the timing belt cover or on the cylinder head. Compare the code you find with the list above. Engine codes are 3 to 6 characters long.
My vehicle is a 2100 model – is it covered?
The compatibility range for this part includes 2100-3130. The 2100 model year falls within this range, but verify the engine code and body type match. Mid-year production changes sometimes mean two vehicles from the same model year use different parts.
Reviews
There are no reviews yet.