6 Pieces Fuel Injector Seal Fit for Audi S4 A5 S5 A6 S6 A8 S8 Volkswagen Touareg 2009-2018
This injector seal kit is engineered as a direct replacement for the Audi S4 A5 S5 A6 S6 A8 S8 Volkswagen Touareg 2009-2018. Manufactured to meet or exceed OEM specifications, it delivers reliable performance in demanding conditions. Each unit is tested for fuel flow, pressure rating, and durability before leaving the factory to ensure consistent quality across every order.
Vehicle Compatibility
| Application | Details |
|---|---|
| Audi S4 A5 S5 A6 S6 A8 S8 | See product specifications |
| Volkswagen Touareg 2009 | 2018 Replacement Part Number: 06E998907E, 06E998907B, 06E998907D, 6E998907E, 06E-998-907-E, 06E-998-907-B, 06E-998-907-D, 06E 998 907 E, 06E 998 907 B, 06E 998 907 D Application: Fit for following models |
| Volkswagen Vehicle:2011 | 2015 |
| Volkswagen Touareg 3.0L V6 | See product specifications |
| Audi Vehicle:2009 | 2015 |
| Audi A6 3.0L V6 A/T2012 | 2015 |
| Audi A7 3.0L V6 A/T2013 | 2018 |
| Audi A8 3.0L V6 A/T2013 | 2017 |
| Audi Q5 3.0L V6 A/T2011 | 2015 |
| Audi Q7 3.0L V6 A/T2015 | See product specifications |
| Audi R8 4.2L V8 A/T2015 | See product specifications |
| Audi R8 4.2L V8 A/T2011 | 2012 |
Replaces OEM Part Numbers
06E998907E • 06E998907B • 06E998907D • 6E998907E • 06E-998-907-E • 06E-998-907-B • 06E-998-907-D • Application • following • models • Volkswagen • Vehicle
Signs You Need a Replacement
If your equipment is showing any of these symptoms, the injector seal kit may be the cause:
- Fuel leak at injector base — Copper washers lose their crush seal over time. If you see dampness around the injector, the seals need replacement.
- Fuel in coolant or oil — A failed combustion seal allows fuel pressure to escape into adjacent passages. This is a serious issue that requires immediate attention.
- Loss of compression on one cylinder — When the copper sealing washer fails, combustion gases blow past the injector body instead of pushing the piston.
Installation Notes
Clean the injector bore thoroughly before installing new seals. Any carbon or debris left in the bore prevents the copper washer from seating properly, causing a compression leak. Use a wire brush or bore cleaning tool, then wipe with a lint-free cloth. Install the seals in the order specified in the kit — the heat shield goes on first, then the copper washer, then the O-rings. Torque the injector to the specified value and recheck after running the engine under load.
Frequently Asked Questions
Which Audi models does this part fit?
Refer to the Vehicle Compatibility table above for the full list of Audi models. Each listing includes the body type, engine, and production years. Match your vehicle’s engine code (stamped on the engine block) against the listed codes to confirm.
Can I cross-reference 06E998907E with 06E998907B?
Yes. Both 06E998907E and 06E998907B are interchangeable OEM numbers for this part. They refer to the same component with the same specifications, just different part number revisions.
This listing is for 6 pieces – do I need to buy a full set?
This listing includes 6 units. For best results, replace all injectors at the same time rather than one at a time. Mixing old and new units causes uneven fuel delivery and shortens the life of the new parts.
My vehicle is a 2009 model – is it covered?
The compatibility range for this part includes 2009-2018. The 2009 model year falls within this range, but verify the engine code and body type match. Mid-year production changes sometimes mean two vehicles from the same model year use different parts.
Reviews
There are no reviews yet.