Fuel Line MIA882574 for Yanmar Engine 4TNV98C 4TNV98CT John Deere Excavator 60P 60G 75P 75G 85P 85G Premium Quality with 3-Year Warranty
This fuel line is engineered as a direct replacement for the Yanmar Engine 4TNV98C 4TNV98CT John Deere Excavator 60P 60G 75P 75G 85P 85G Premium Quality with 3-Year Warranty. Manufactured to meet or exceed OEM specifications, it delivers reliable performance in demanding conditions. Each unit is tested for fuel flow, pressure rating, and durability before leaving the factory to ensure consistent quality across every order.
Vehicle Compatibility
| Application | Details |
|---|---|
| Yanmar Engine 4TNV98C 4TNV98CT | See product specifications |
| John Deere Excavator 60P 60G 75P 75G 85P 85G Premium Quality with 3 | Year Warranty Replacement Part Number: MIA882574 Fit for |
| Yanmar Engine: 4TNV98C, 4TNV98C | PJLW2, 4TNV98CT, 4TNV98CT-PJLW, 4TNV98T Application: Fit for following models |
| John Deere Loader:204L, 210G, 210LEP, 244P, 244K, 244K | II, 244L, 304L, 310G, 310LEP, 318E, 319E, 320E, 320G, 323E, 324P, 324E, 324G, 324K, 324L, 325G, 326P, 326E |
| John Deere Excavator: 60P, 60G, 75P, 75G, 85P, 85G | See product specifications |
| Hitachi Excavator: ZAXIS60USB | 5N, ZAXIS75US-5N, ZAXIS85USB-5N |
Replaces OEM Part Numbers
MIA882574 • Yanmar • Engine • 4TNV98C • 4TNV98C-PJLW2 • 4TNV98CT • 4TNV98CT-PJLW • 4TNV98T • Application • following • models • Deere
Signs You Need a Replacement
If your equipment is showing any of these symptoms, the fuel line may be the cause:
- Fuel smell or visible wet spots — A cracked or perished fuel line seeps fuel. Diesel fuel lines harden with age and develop hairline cracks near connection points.
- Air in the fuel system — Air enters through deteriorated hoses, causing hard starting and rough running. Check all connections and replace any line that feels spongy.
- Collapsed line under suction — A reinforced fuel line can collapse internally, restricting flow. The engine runs fine at idle but starves under load.
- Fuel leaking at connection points — Old clamps lose tension and the hose shrinks over time. Always use new clamps when installing fuel lines.
Installation Tips
When installing new fuel lines, cut the ends square with a sharp blade — angled cuts cause leaks at the connection points. Use new clamps at every connection; old clamps have lost their spring tension. After installation, pressurize the system with the primer pump and check every fitting for dampness. Run the engine and recheck after 10 minutes of operation, as fittings can loosen slightly under vibration.
Frequently Asked Questions
Will this fit my John Deere 60P?
Yes. This part is designed to fit the John Deere 60P, 60G, 75P, 75G among other models listed in the compatibility table above. Verify your specific model and engine code before ordering to ensure the correct fit.
Can I cross-reference MIA882574 with Yanmar?
Yes. Both MIA882574 and Yanmar are interchangeable OEM numbers for this part. They refer to the same component with the same specifications, just different part number revisions.
What material are these fuel lines made from?
This fuel line kit uses materials rated for the specific fuel type and pressure of your application. Diesel lines need to handle higher pressure than gasoline lines. Always install the correct fuel-rated line and use new clamps at every connection point.
What tools do I need to install this on a John Deere?
Standard metric hand tools will handle most of the job – sockets, wrenches, and a torque wrench. For John Deere equipment, check the specific service manual for any special tools or torque values.
Reviews
There are no reviews yet.